Category: Maintenance

Categories
Educational Filtration Maintenance

Oasis Tilt ‘N Tether

OASIS Tilt ‘N Tether

Tired of laying on the floor to change a filter? 

Tired of something that should take minutes taking twenty?

What’s Your Time Worth?

Do the math: An estimated 15 minutes saved per every filter change x labor = $ SAVINGS!

ACCESSIBILITY

Easy access to filter with just two screws to open
bottle filler.

CONVENIENCE

One screwdriver needed – keeping it simple
on your toolbox.

EFFICIENT

Filter replacement and/or maintenance can
be performed in under two minutes.

Only OASIS can deliver

• Painless maintenance with large opening in the bottle
filler, prevention of cuts/bruises on hands

• Fast access to bottle filler programming, main controls,
and hands-free troubleshooting

• Easy on the customer with functional features like the
integrated bottle counter and filter status

• Easy on the plumber with OASIS Tilt ‘N Tether for handsfree
filter changes without frustration


CONTACT US

Categories
Maintenance

How To: Restart Your Water Fountain

It’s that exciting time of year again – Back-to-School season for Fall 2023! OASIS is here to help give the school year a refreshing start with recommended instructions for bringing a cooler back into service after being shut down.

Supplies Required for the OASIS PG8AC unit

  • Disinfectant wipes or food grade disinfectant
  • Latex or nitrile gloves
  • T 15 Torx Screwdriver
  • Bucket
  • ¼” Union part #028605-101

Step 1 – Unplug Unit

  • Remove front cover (if necessary) to access electric plug
  • Unplug from outlet

Step 2 – Prep the Cooler

  • Shut off water valve – note this is for example only, actual valves can differ
  • Press dispense pad until water stops to depressurize

Step 3 – Bypass the Filter (if applicable)

  • This is a great time to change the filter cartridge
  • Remove the tubing from the filter head

Step 4 – Draining the Cold Tank

Depress the collet and remove the drain plug
Allow tank to drain to completely into bucket.
Note – Some models may have a cap instead of a plug.

Step 5 – Closing the Tank Drain

  • Insert the plug into the union fitting to close the tank drain
  • Insert the cap onto the drain line to close the tank drain

Step 6 – 1st Flush Cycle

  • Turn ON water supply
  • Depress pad until water fills the cold tank and runs consistently, allow approximately 2 gallons

Step 7 – Repeat Draining the Cold Tank

Shut off water supply
Depressurize
Remove drain plug on tank
Drain into bucket

Step 8 – 2nd Flush Cycle

  • Turn ON water supply
  • Run 2 more gallons through the unit

Step 9 – Reconnect the Filter (if applicable)

  • Shut off water and depressurize the unit once more
  • Note – It is recommended to properly flush the replacement filter cartridge before connecting to the cooler
  • Remove lines from union
  • Reinsert the tubing into the filter head

Step 10 – Flushing Complete

  • Turn ON water supply
  • Run water by depressing the dispense pad
  • Plug unit back into outlet

Step 11 – Sanitizing the Exterior

  • Clean the top of the unit, push pads and bubbler with disinfectant wipes
Categories
Education Maintenance

Upgrade Your K-12 Hydration Solutions

ESSER II expiring September 30, 2023
ESSER III expiring September 30, 2024

ESSER Funding Overview
ESSER funding is a federal grant program that provides funding to states and local educational agencies (LEAs) to help them address the impact of COVID-19 in education. The ESSER funds can be used to improve K-12 public schools infrastructure to reduce risk of virus transmission and exposure to environmental health hazards, and to support student health needs.


Investing ESSER II & III funding in hygienic hydration solutions, such as contactless bottle-filling stations and drinking fountains with filtration systems targeting lead and other harmful contaminants is essential to ensure students’ access to safe and clean drinking water.


You have the grant money, OASIS has the products. Act now and install units over holiday breaks. Providing clean drinking water is essential for a healthy future for ourselves and our students.

How can I use my awarded ESSER funding?

  1. Replace old units to contactless bottle filling stations and drinking fountains, reducing the risk of virus transmission
  2. Upgrade your filtration systems for safe, clean drinking water
  3. Focus on your sustainability goals, reducing the use of single use plastic and waste with bottle filling stations

There is money still left in ESSER funds with limited time to spend it. Act now and install over holiday breaks!

CONTACT Oasis
Categories
Installation Maintenance

Electronic Bottle Filler Programming

Easily program your electronic bottle fillers after installation or maintenance!

Welcome to the OASIS bottle filler programming guide. To begin open your box and confirm that there is a programmer along with a battery pack. Click the top button and see how much charge it has. It recharges to include a micro USB cable.

To begin with, plug in the programer to the battery pack in the back. You should see all the lights light up and then switch to a blue blinking light on the status.

Open up your OASIS bottle filler and locate the PCB on the back of the unit. You will have to line up three locating pins next to the large black chip, with the three locating pins on the programmer. After you have it all connected hit the button on the front of the programmer and watch as the lights will flash. Wait until the status light turns green and the active light resumes flashing blue.

After that, remove the programmer and using the button attached to the PCB – click once. You should then see on the front it say FW REV 16.24 (Firmware Revision).

Questions or issues? Contact us; our tech services specialists can assist with installation walk-throughs, troubleshooting, and product and technical questions.

OASIS Technical Support

Phone: 800.646.2747

Email: tech@oasiscoolers.com

Categories
Maintenance Press Release

Oasis Bottle Filler Updates Water Fountains

The VersaFiller® Bottle Filler Retrofit from Oasis® International turns an existing water cooler into a versatile bottle-filling station. An exclusive adaptor gasket allows it to be installed on today’s most common water coolers.
More than 60 million plastic water bottles are thrown away every day, and each will take 700 years to decompose. Because of this, more people are carrying their own repeat-use water bottles and want to be able to refill them on the go. They do it to be more responsible about the environment and to save on the cost of buying single-serve water.

Without the need for a major capital expenditure, any facility—healthcare centers, schools and universities, corporate campuses, multi-unit housing, hotels and resorts—can retrofit existing water coolers and upgrade them to include modern bottle-filling stations.

Continue reading “Oasis Bottle Filler Updates Water Fountains”
OASIS is a registered trademark of LVD Acquisition, LLC dba Oasis International © 2022